Company info

METALLOPROM-PIVDEN Ltd. is situated on the territory of 8 hectares in the industrial area in the suburbs of Odessa city, big commercial and trading center of Ukraine near three large deep-sea ports. Odessa port is within 20 km distance, Yuzhniy – 25 km, Ilyichevsk – 60 km

Industrial facilities are situated in two workshops:

Workshop No. 1 – total area 20,000 sq. m
Workshop No. 2 – total area 6,000 sq. m (can be extended up to 20,000 sq. m)

ISO 9001-2009 CERTIFICATE NO. UA 2.027.05283-10

Workshop №1

The following equipment is situated in workshop No. 1:

PLATE SHOT-BLASTING AND COATING LINE (“ROSLER”, GERMANY)

The line consists of: - leveling machine;

  • pre-drying chamber;
  • shot-blasting chamber;
  • painting chamber;
  • drying chamber.

The line is equipped with roll gang system. Plates in thickness from 3 up to 70 mm can be processed by this line. Maximum width of the plate is 3200 mm. Maximum length of the plate is 15000 mm. It is possible to shot-blast and paint plates and metalware of maximum width 4000 mm and maximum length 24000 mm

The line allows to make shot-blasting of a plate upto different levels in accordance with ISO 8501 and to paint in various thickness with zinc silicate primers according to ISO 12944 and special requirements of a customer.

P-4 mill

The mill cuts hot rolled and cold rolled coils of ordinary, low-carbon, low-alloy and stainless steel grades in thickness from 0.5 to 6 mm of maximum width 1500 mm into sheets, with or without edge trimming according to GOST 19903-74 and 19904-90 and into strip of minimum width 50 mm in accordance with TU-1415-305-93.

Mill for processing secondary coils

The mill cuts hot rolled and cold rolled prime and secondary coils in thickness from 0.5 to 8 mm of maximum width of 1500 mm into sheets, without edge trimming.

Mill for rolling rolled-formed sections and sections for mounting gypsum plasterboards.

Sections for mounting gypsum plasterboards are rolled on this mill according to TU-1122-001-80392468-2009 out of galvanized metal-roll produced according to GOST 14918-80.

Mill for rolling С-10 and С-44 sections

Sections in accordance with GOST 24045-99 are produced on this mill.

Workshop №2

The following equipment is situated in workshop No. 2:

Oxy/plasma cutting machines – 3 units:

  • with working zone 2500 x 8000 mm, equipped with 1 plasma cutter AUTO CUT 300 for metal in thickness 1 – 50 mm, 1 oxy cutter for metal in thickness 5 – 300 mm;
  • with working zone 3200 x 14000 mm, equipped with 1 plasma cutter AUTO CUT 300 for metal in thickness 1 – 50 mm, 2 oxy cutters for metal in thickness 5 – 300 mm;
  • with working zone 6000 x 16000 mm, equipped with 2 straight oxy cutters for metal in thickness 1 – 200 mm, 2 rotating three-cutters blocks for thickness 12 – 70 mm.

Oxy/plasma cutting is performed in accordance with ISO 9013.

3 oxy/plasma cutting machines “PIRSE” (Czech Rep.) with working zone 6000 x 45000 mm are to be soon installed, which will allow to significantly increase our monthly production volumes.

Off-grade plate finishing zone

Bending machine

Rolling press for rolling cylinder

Combined shearing press

Guillotine

Repair base

The enterprise has its own repair base and the following metal-cutting equipment:

Turning machine – 3 units;

Milling machine – 2 units;

Grinding machine – 1 unit;

Drilling machine – 2 units; Planing machine – 2 units.

Warehouses

Steel products are stored at:

  • Warehouse for coils – 9,000 sq. m of covered area.
  • Warehouse for ready-made products – 5,000 sq. m of covered area.

All warehouses and workshops are equipped with bridge cranes with lifting capacity from 5 to 25 tn.

A “Linde-gaz” (Germany) cryogenic 27 m³ tank with liquid oxygen which is delivered to the workshops by pipelines is installed at the premises of METALLOPROM. There is also natural gas supply for industrial consumption.

The enterprise has two high-voltage power supply inputs 10,000 kVa each.

METALLOPROM has its own railway branch line.
The trucks of our own can also be used to carry steel products.